Careers › Electrical & Electronics Engineering › Analog Design Engineer
For students and early-career professionals
Designs analog circuits like amplifiers and sensors where noise and precision matter.
12 chapters · About 3 months · 15–30 min a day
Start this plan free → Chapter 1 is free.
What's in the plan
Skills 10 skills Analog circuit design, Circuit simulation, Test and measurement and 7 more. See what you'll learn
Practice 12 practice tasks Tasks from the real work of the job, 10 to 35 minutes each
Projects 2 projects you keep Stability and Noise Check on a Published Op-Amp Circuit Buck converter: build, measure efficiency, explain the losses
Interview 20 interview questions Practise your answers, with feedback
People 4 people to reach Who they are, with 4 messages ready to send
Also: choose your route in (7 credentials compared, none required) and 3 life skills courses.
Skills
10 skills, and what you'll learn in each
Each skill is a few short lessons, then practice. You rate yourself at the start and again at the end.
Core to the job
Chapter 2
Analog circuit design Design a filter that reduces noise in a sensor signal
What you'll learn
DC bias point Gain and bandwidth Noise budget Stable feedback loop Practice
Design and Simulate a Low-Pass RC Filter for a Sensor Signal25 min Stability-Check a Voltage-Follower Op-Amp Stage and Fix a Capacitive Load Problem35 min Chapter 2
Circuit simulation Simulate a circuit and check it against your hand calculation
What you'll learn
DC AC transient Component models Simulation convergence Tolerance analysis Measurement comparison Practice
Build and Simulate a Voltage Divider in LTspice15 min Simulate an RC Low-Pass Filter and Read Its Bode Plot20 min Chapter 5
Test and measurement Set up lab instruments and take readings you can trust
What you'll learn
Setup shapes the reading Timebase and trigger Probe loading Ground-lead inductance Sanity-check against theory Practice
Measure 3 values on a USB charger15 min Estimate wafer yield from defect density25 min Chapter 5
Engineering test planning Plan product tests covering normal use, limits and expected failures
What you'll learn
Verification and validation Acceptance criteria Corner conditions Characterisation test Practice
Plan 8 test cases for a new product20 min Build a Test Checklist for a Microcontroller Board15 min Chapter 6
Design for manufacturing Review a design or parts list and spot factory problems
What you'll learn
Testability Design rules Component footprints Second sourcing DFM feedback Chapter 8
Technical writing Write a one-page work summary and a handover note
What you'll learn
State your assumptions Trade-offs on the page Reproducible test report Comment the why App-note structure Draft or record Precise procedure step Practice
Write a Bench Test Report for a Power Supply15 min
4 more in the plan
Problem solving Test each possible cause of a problem instead of guessing Ch 7 What you'll learn
Problem vs symptom Clean problem splits Root cause Deciding under uncertainty Practice
Separate the Problem from the Symptom10 min Adapting to change Try a new tool and describe how you handled change Ch 7 What you'll learn
Change vs your response The messy in-between Not there yet Real change vs a feeling Practice
Map a Change You've Already Survived15 min Communication Rewrite an update for two different readers, cutting extra lines Ch 8 What you'll learn
Lead with the point Match detail to the reader Said versus heard Specific feedback Practice
Write a Six-Line Delay Message10 min Working with others Contribute to group work, ask for help and credit teammates Ch 8 What you'll learn
Early team friction Clear ownership Challenge ideas, not people Lead or follow
Your plan
Chapter by chapter. 12 chapters, in this order. Chapter 1 is free.
1 ~1 wk See what analog design engineer work involves Start Free
2 ~1 wk Design analog circuits and simulate them first Skills
3 1–2 wks Check stability and noise in an amplifier Project
4 ~1 wk Talk to an working analog engineer People
5 ~1 wk Plan tests and measure results honestly Skills
6 ~1 wk Design products a factory can build Skills
7 ~1 wk Solve problems when plans change Skills
8 ~1 wk Write technical documents people can use Skills
9 1–2 wks Capstone: build a buck converter and explain losses Project
10 ~1 wk Answer the questions interviewers ask Interview
11 ~1 wk Decide how you will get in Decide
12 on your timeline Send your first applications Apply
The job
What a Analog Design Engineer does Designs low-noise analog circuits for electronic products so signals are accurate, stable, and manufacturable.
The work Design analog circuits like amplifiers, filters, references, and sensor front-ends Analyze noise, offset, drift, stability, and power tradeoffs to meet specs Simulate circuits across corners, temperature, and supply variation Review layouts for matching, parasitics, and signal integrity risks Build lab setups to measure performance and debug issues on silicon or boards Coordinate with digital, layout, test, and systems teams to integrate blocks Document designs, assumptions, and test results for reuse and sign-off A typical day Review specs, past test data, and decide what to change in the next iteration Run simulations, compare results to targets, and update schematics Meet with layout and systems to align on constraints and interfaces In the lab, measure noise, gain, and stability, then troubleshoot mismatches Write short design notes and plan the next set of experiments Tools EDA: Cadence Virtuoso, Spectre Simulation: SPICE, Monte Carlo Lab instruments: oscilloscope, spectrum analyzer Prototyping: breadboard, evaluation boards Scripting: Python, MATLAB Documentation: datasheets, design reviews
Ways in
There is more than one route. Ways to study Bachelor degree in electrical engineering or electronics engineering Master degree focused on analog or mixed-signal IC design Technical diploma plus strong lab experience in electronics and measurement Online courses plus a portfolio of measured analog circuit projects How people get their first job Apply for analog design or mixed-signal internships and co-op placements Start in electronics test engineering to learn measurement and debug skills Build a portfolio: measured op-amp, filter, and sensor interface projects Join a university lab or student team working on hardware prototypes Contribute to open hardware designs and write clear test reports Life skills in this plan: Networking · Job interviews · Job search
How the work is changing
What AI is doing to this role How AI is changing this role · one of 6 tasks we track
Simulate across process corners and temperature Sped up a lot
What AI does Spectre and Monte Carlo runs get set up and sifted for you.
Still yours Reading what a corner failure means for real silicon takes years.
Reviewed September 2026
In the app · Premium
The rest is in the app
How AI affects the other 5 tasks Whether this job is growing or shrinking How hard the first job is to get Similar roles that are easier to get into Updated every month, with sources
See it in the app →
How we rate a job →
Already working
Already a Analog Design Engineer? Plan your move to Senior Analog Design Engineer: 10 chapters that end with a strong case for your next review.
Grow in the role →
Other roles in Electrical & Electronics Engineering
Questions
Questions about this plan How long does it take to become a analog design engineer with Welica? The plan is 12 chapters, 3 months at 15 to 30 minutes a day. You can go faster or slower; the plan moves with you.
Do I need a degree? Not always. Common routes are bachelor degree in electrical engineering or electronics engineering, master degree focused on analog or mixed-signal IC design, technical diploma plus strong lab experience in electronics and measurement, or online courses plus a portfolio of measured analog circuit projects.
What is free? Chapter 1, See what analog design engineer work involves, is free for good. Premium unlocks the rest of the plan.
Start the Analog Design Engineer plan. Chapter 1 free. About 15 to 30 minutes a day.
Already have an account? Sign in