For students and early-career professionals

Electronics Technician

Builds, tests, and repairs electronic equipment using tools, schematics, and measurement devices.

12 chapters · About 4–5 months · 15–30 min a day

Start this plan free →

Chapter 1 is free.

Skills

9 skills, and what you'll learn in each

Each skill is a few short lessons, then practice. You rate yourself at the start and again at the end.

Core to the job

Chapter 2

Reading schematics

Trace a circuit drawing on paper and find the error

What you'll learn

  • Standard symbols
  • Signal flow
  • Loop diagram
  • Drawing discrepancy

Practice

  • Sketch and explain an aircraft electrical bus30 min
  • Trace a Simple Circuit and Find the Error15 min

Chapter 4

Soldering and rework

Solder clean joints and replace a board component without damage

What you'll learn

  • Good wetting
  • Heat and flux
  • Common joint defects
  • Safe rework sequence

Practice

  • Identify and label 10 electronic components20 min
  • Solder three joints and inspect them30 min

Chapter 4

Tool use

Pick the right tool and spot unsafe substitutes

What you'll learn

  • Right tool for the job
  • Torque to spec
  • Pull test
  • Tool condition

Chapter 4

Using a multimeter

Choose a meter setting, then explain what the reading means

What you'll learn

  • Meter function choice
  • Lead positions
  • Live measurement safety
  • Known source check
  • Sensible reading check

Practice

  • Practise multimeter readings on household items20 min
  • Pick the right test instrument for five jobs20 min

Chapter 6

Root cause analysis

Keep asking why something failed until you reach the cause

What you'll learn

  • Root cause vs symptom
  • 5 Whys
  • Fishbone diagram
  • Systemic cause, not blame
  • Containment vs permanent fix

Practice

  • Find the Root Cause in an Alarm Cascade20 min

4 more in the plan

CommunicationRewrite an update for two different readers, cutting extra linesCh 7

What you'll learn

  • Lead with the point
  • Match detail to the reader
  • Said versus heard
  • Specific feedback

Practice

  • Write a Six-Line Delay Message10 min
Working with othersContribute to group work, ask for help and credit teammatesCh 7

What you'll learn

  • Early team friction
  • Clear ownership
  • Challenge ideas, not people
  • Lead or follow
Customer communicationExplain a problem without jargon, then say what to expectCh 7

What you'll learn

  • Plain language over jargon
  • Setting expectations
  • Fact versus story
  • A de-escalation sequence (HEAT)
  • Bad news early

Practice

  • Explain a Breaker Replacement to a Homeowner10 min
Adapting to changeTry a new tool and describe how you handled changeCh 8

What you'll learn

  • Change vs your response
  • The messy in-between
  • Not there yet
  • Real change vs a feeling

Practice

  • Map a Change You've Already Survived15 min

Your plan

Chapter by chapter.

12 chapters, in this order. Chapter 1 is free.

1~2 wks

See the work of an Electronics Technician

StartFree
2~2 wks

Read schematics and wiring diagrams

Skills
3~2 wks

Film a lockout-tagout safety walkthrough

Project
4~2 wks

Solder, test and repair at the bench

Skills
51–2 wks

Talk to two working electronics technicians

People
6~2 wks

Find what really broke and why

Skills
7~2 wks

Explain your work so customers stay calm

Skills
8~2 wks

Adapt well when work changes

Skills
9~2 wks

Capstone: build a wiring harness and test it

Project
101–2 wks

Answer the questions interviewers ask

Interview
111–2 wks

Decide how you will get in

Decide
12on your timeline

Send your first applications

Apply

The job

What a Electronics Technician does

Tests, troubleshoots, and repairs electronic equipment for teams and customers so devices work safely and reliably.

The work

  • Read schematics and service manuals to understand circuits and signals
  • Test boards and devices using meters, oscilloscopes, and signal sources
  • Diagnose faults by tracing signals and checking components
  • Repair or replace parts using soldering and rework techniques
  • Calibrate equipment and verify performance against specifications
  • Document repairs, test results, and parts used for traceability
  • Support production by finding recurring defects and suggesting fixes

A typical day

  1. Review work orders, safety notes, and test requirements for the day
  2. Run diagnostics, measure signals, and isolate the failing section
  3. Solder or swap components, then retest to confirm the fix
  4. Update logs, label units, and hand off to the next process or customer

Tools

Test equipment: multimeter, oscilloscope, logic analyzerSoldering tools: soldering iron, hot air rework, fluxHand tools: screwdrivers, crimpers, wire strippersDocumentation: service manuals, work orders, checklistsComputer tools: spreadsheets, ticketing systemsESD control: wrist strap, mat, ESD-safe storage

Ways in

There is more than one route.

Ways to study

  • Technical diploma in electronics or electrical technology
  • Vocational training in electronics repair and test
  • Apprenticeship or paid trainee program in maintenance or manufacturing
  • Certificate courses in soldering, ESD, and basic circuit analysis

How people get their first job

  • Apply for electronics repair trainee or test technician roles
  • Join a manufacturing or maintenance apprenticeship with electronics work
  • Build a small portfolio of repairs with before and after test notes
  • Earn a soldering and ESD handling certificate and practice on kits
  • Volunteer to maintain audio, lighting, or lab equipment at a school or club

How the work is changing

What AI is doing to this role

How AI is changing this role · one of 6 tasks we track

Read schematics and understand circuits

Sped up a lot

What AI does

AI tools can explain circuit blocks and flag likely failure points.

Still yours

You still verify on the bench with real signals.

Reviewed September 2026

In the app · Premium

The rest is in the app

  • How AI affects the other 5 tasks
  • Whether this job is growing or shrinking
  • How hard the first job is to get
  • Similar roles that are easier to get into
  • Updated every month, with sources
See it in the app →

How we rate a job →

Already working

Already a Electronics Technician?

Plan your move to Senior Electronics Technician: 8 chapters that end with a strong case for your next review.

Grow in the role →

Other roles in Electrical & Instrumentation Trades

Questions

Questions about this plan

How long does it take to become a electronics technician with Welica?

The plan is 12 chapters, 4–5 months at 15 to 30 minutes a day. You can go faster or slower; the plan moves with you.

Do I need a degree?

Not always. Common routes are technical diploma in electronics or electrical technology, vocational training in electronics repair and test, apprenticeship or paid trainee program in maintenance or manufacturing, or certificate courses in soldering, ESD, and basic circuit analysis.

What is free?

Chapter 1, See the work of an Electronics Technician, is free for good. Premium unlocks the rest of the plan.

Start the Electronics Technician plan.

Chapter 1 free. About 15 to 30 minutes a day.

Start on web Continue your session Download for MacMac Get the iPhone appiPhone Get it on Google PlayAndroid