For students and early-career professionals

Electrical Engineering Technician

Assists engineers by building prototypes, wiring panels, and running electrical tests.

12 chapters · About 4–5 months · 15–30 min a day

Start this plan free →

Chapter 1 is free.

Skills

9 skills, and what you'll learn in each

Each skill is a few short lessons, then practice. You rate yourself at the start and again at the end.

Core to the job

Chapter 2

Tool use

Pick the right tool and spot unsafe substitutes

What you'll learn

  • Right tool for the job
  • Torque to spec
  • Pull test
  • Tool condition

Chapter 2

Soldering and rework

Solder clean joints and replace a board component without damage

What you'll learn

  • Good wetting
  • Heat and flux
  • Common joint defects
  • Safe rework sequence

Practice

  • Solder three joints and inspect them30 min
  • Plan a Rework Job on a Damaged PCB20 min

Chapter 2

Reading schematics

Trace a circuit drawing on paper and find the error

What you'll learn

  • Standard symbols
  • Signal flow
  • Loop diagram
  • Drawing discrepancy

Practice

  • Sketch and explain an aircraft electrical bus30 min
  • Trace a Simple Circuit and Find the Error15 min

Chapter 4

Electrical troubleshooting

Find why a fan won't spin by testing in steps

What you'll learn

  • Expected system behaviour
  • Half-split method
  • Evidence before replacement
  • Circuit diagram
  • Meter reading

Practice

  • Diagnose a motor that won't start25 min
  • Diagnose Why a Fan Won't Spin15 min

Chapter 6

Code compliance

Cite the rule that applies and check work against it

What you'll learn

  • Applicable code
  • Code structure
  • Adopted edition
  • Inspection evidence

4 more in the plan

Problem solvingTest each possible cause of a problem instead of guessingCh 4

What you'll learn

  • Problem vs symptom
  • Clean problem splits
  • Root cause
  • Deciding under uncertainty
CommunicationRewrite an update for two different readers, cutting extra linesCh 7

What you'll learn

  • Lead with the point
  • Match detail to the reader
  • Said versus heard
  • Specific feedback

Practice

  • Write a Six-Line Delay Message10 min
Working with othersContribute to group work, ask for help and credit teammatesCh 7

What you'll learn

  • Early team friction
  • Clear ownership
  • Challenge ideas, not people
  • Lead or follow

Practice

  • Write a Request That Makes It Easy to Say Yes10 min
Adapting to changeTry a new tool and describe how you handled changeCh 8

What you'll learn

  • Change vs your response
  • The messy in-between
  • Not there yet
  • Real change vs a feeling

Practice

  • Map a Change You've Already Survived15 min

Your plan

Chapter by chapter.

12 chapters, in this order. Chapter 1 is free.

1~2 wks

See the work of an Electrical Engineering Technician

StartFree
2~2 wks

Read schematics and solder reliable joints

Skills
3~2 wks

Make a lockout safety video and checklist

Project
4~2 wks

Find electrical faults fast

Skills
51–2 wks

Talk to two working electrical technicians

People
6~2 wks

Keep your work to code and standard

Skills
7~2 wks

Make yourself understood across a team

Skills
8~2 wks

Adapt well when work changes

Skills
9~2 wks

Capstone: build and test a wiring harness

Project
101–2 wks

Answer the questions interviewers ask

Interview
111–2 wks

Decide how you will get in

Decide
12on your timeline

Send your first applications

Apply

The job

What a Electrical Engineering Technician does

Help engineers build, wire, and test electrical devices and control panels so products and systems work safely and reliably.

The work

  • Build and wire prototypes from schematics and wiring diagrams
  • Assemble control panels and route cables to good safety standards
  • Set up and run electrical tests on circuits, sensors, and power supplies
  • Use meters and scopes to measure signals and find faults
  • Document test results, changes, and build notes for engineers
  • Troubleshoot wiring, connectors, and components to fix failures
  • Support lab and workshop safety, including lockout and safe handling

A typical day

  1. Review drawings and test plans, then gather parts and tools
  2. Build or rework a prototype, label wires, and check connections
  3. Run tests, record readings, and report issues to the engineer
  4. Join a short check-in to plan next steps and parts needed
  5. Update logs and clean up the bench for the next build

Tools

Test equipment: multimeter, oscilloscope, function generatorHand tools: wire strippers, crimpers, torque driversSoldering: soldering iron, hot air reworkDocumentation: spreadsheets, lab notebooksCAD viewing: electrical schematics viewersPower tools: drill, heat gun

Ways in

There is more than one route.

Ways to study

  • Technical diploma in electrical engineering technology
  • Vocational training in electrical or electronics technology
  • Apprenticeship with classroom training and supervised lab work
  • Certificate program in industrial electronics or controls

How people get their first job

  • Apply for technician internships in labs, factories, or utilities
  • Start as a production test technician and learn test procedures
  • Build a small portfolio of wired projects with photos and test notes
  • Earn a basic electrical safety certification from a recognized provider
  • Volunteer in a school lab or makerspace to practice wiring and soldering

How the work is changing

What AI is doing to this role

How AI is changing this role · one of 6 tasks we track

Document test results and build notes

Sped up a lot

What AI does

Templates and auto-capture reduce time writing results by hand.

Still yours

You add the engineering notes only you can write.

Reviewed September 2026

In the app · Premium

The rest is in the app

  • How AI affects the other 5 tasks
  • Whether this job is growing or shrinking
  • How hard the first job is to get
  • Similar roles that are easier to get into
  • Updated every month, with sources
See it in the app →

How we rate a job →

Already working

Already a Electrical Engineering Technician?

Plan your move to Senior Electrical Engineering Technician: 8 chapters that end with a strong case for your next review.

Grow in the role →

Other roles in Electrical & Instrumentation Trades

Questions

Questions about this plan

How long does it take to become a electrical engineering technician with Welica?

The plan is 12 chapters, 4–5 months at 15 to 30 minutes a day. You can go faster or slower; the plan moves with you.

Do I need a degree?

Not always. Common routes are technical diploma in electrical engineering technology, vocational training in electrical or electronics technology, apprenticeship with classroom training and supervised lab work, or certificate program in industrial electronics or controls.

What is free?

Chapter 1, See the work of an Electrical Engineering Technician, is free for good. Premium unlocks the rest of the plan.

Start the Electrical Engineering Technician plan.

Chapter 1 free. About 15 to 30 minutes a day.

Start on web Continue your session Download for MacMac Get the iPhone appiPhone Get it on Google PlayAndroid